|
|
Post by DocSpeed on Sept 5, 2005 22:32:00 GMT -5
Change the fluid in the S10 earlier today. Started running through all the gears after I got all the fluid in and noticed that it doesn't want to pull while shifted into 2nd on the dash from a dead stop. Strange, pulls hard in all foward gears except when manually shifted into 2nd from a dead stop. I have no problems with the tranny shifting around 2nd going down the road even when I hammer on the gas or take off from a dead stop as long as it is not manually shifted into 2nd. Any ideas??  |
|
|
|
Post by DocSpeed on Sept 5, 2005 22:36:14 GMT -5
By the way, I forgot to mention that It was doing this before I changed the fluid. I just forgot about the problem till today.
|
|
|
|
Post by AAron on Sept 5, 2005 23:19:49 GMT -5
so in drive it works fine? under acceleration
|
|
|
|
Post by DocSpeed on Sept 6, 2005 0:21:47 GMT -5
Yeah, strange huh? Wonder if it is an electronics problem?
|
|
|
|
Post by metalbeast on Sept 6, 2005 7:07:25 GMT -5
Do you think it has anything to do with that B&M shift programmer you installed on it?
|
|
|
|
Post by DocSpeed on Sept 6, 2005 7:38:40 GMT -5
It has been an issue since I bought it. It drives fine, I would like to know why it doesn't pull from a stop when its shifted manually into second.
|
|
|
|
Post by AAron on Sept 6, 2005 10:10:21 GMT -5
because it is an AUTO not a MANUAL  i had a T-bird that did that too and so i just stopped shifting it manually and as far as i know it still is running. the B&M shift programer is not a shift kit, correct? if it isnt i would take it off and see what happens for a little bit |
|
|
|
Post by DocSpeed on Sept 6, 2005 16:01:55 GMT -5
It has been an issue since I bought it. It drives fine, I would like to know why it doesn't pull from a stop when its shifted manually into second. I worded this post wrong. I meant the tranny has been acting funny since I bought my truck. |
|
|
|
Post by AAron on Sept 6, 2005 17:00:23 GMT -5
hmm. are you starting out in 2nd? or starting out in 1st then shifting to 2nd?
|
|
|
|
Post by DocSpeed on Sept 6, 2005 20:03:37 GMT -5
Only does when starting out with the gear selector in 2nd. Doesn't do it with 1st,3rd,and 4th.
|
|
|
|
Post by AAron on Sept 6, 2005 23:55:41 GMT -5
im not positive but it might be actually starting off in 2nd gear, i know 3rd will start off in 1st and go through the gears. they might be that way from the factory as a safty thing like icy weather. not sure.
|
|
|
|
Post by DocSpeed on Sept 7, 2005 0:57:31 GMT -5
Never thought of that.... You may be right. I will see if I can't find out some info over the net somewhere.
|
|
|
|
Post by AAron on Sept 7, 2005 9:24:33 GMT -5
you might also cheack the owners manual as well.
|
|
|
|
Post by DocSpeed on Sept 8, 2005 19:17:55 GMT -5
Good idea, if I can find it..... The more I think about it, I really doubt anything is really wrong with the tranny.
|
|
|
|
Post by metalbeast on Sept 9, 2005 6:42:40 GMT -5
Good idea, if I can find it..... The more I think about it, I really doubt anything is really wrong with the tranny. Last time I drove it from Ronald's house it seemed to shift like a champ. I still think it is that POS programmer that is on it. |
|
|
|
Post by DocSpeed on Sept 9, 2005 7:23:38 GMT -5
It does it with or without the shift improver, it was doing it the first week I bought the truck.
|
|
